| Versatile, standards-based IP Intercom and PA device with contact closure inputs and relay output. The Barix Annuncicom 100 is a versatile IP Intercom and PA device, capable of full duplex (bidirectional)streaming of uncompressed audio formats, |
 |
|
Versatile, standards-based IP Intercom and PA device with contact closure inputs and relay output. The Barix Annuncicom 100 is a versatile IP Intercom and PA device, capable of full duplex (bidirectional)streaming of uncompressed audio formats, |
 |
- 2-watt speaker amplifier (into 8 ohms)
- Electret/dynamic microphone input with 3-volt bias supply
- Line-level input and output on Cinch connectors
- 2 contact closure inputs
- 1 relay output with normally open and normally closed contacts rated to 50V, 1 amp
|
- 2-watt speaker amplifier (into 8 ohms)
- Electret/dynamic microphone input with 3-volt bias supply
- Line-level input and output on Cinch connectors
- 2 contact closure inputs
- 1 relay output with normally open and normally closed contacts rated to 50V, 1 amp
|
| Audio over IP encoder with line level and S/PDIF audio inputs, low power, MP3 and PCM, u-law, and a-law support. Support for Multicast and operation as a shoutcast source. |
 |
Audio over IP decoder with line-level audio outputs and USB flash memory interface, low power, multi-format (MP3/WMA/AACplusV2,PCM, Ether-ound) support. |
 |
- Audio stereo encoder for MPEG1&2 Layer3 (MP3, VBR support only), PCM linear and a-law, u-law, 8-48k sample rate support
- 10/100 Mbit Ethernet interface
- Wide range power supply input with low power consumption
- One RS-232 serial port
- IR decoding capability
- IR generation capability (for source control)
- Unbalanced stereo line-level input
- S/PDIF optical input
- S/PDIF coaxial input
|
- Line level (4.2Vpp), unbalanced, stereo output
- 3.5mm headphone jack
|
| Audio over IP decoder with line-level audio outputs, USB flash interface, IR receiver, LCD display and relay, low power, multi-format (MP3/WMA/AACplusV2,PCM,Ethersound) support. |
 |
Audio over IP decoder with line-level audio outputs, USB flash interface, IR receiver, LCD display and relay, low power, multi-format (MP3/WMA/AACplusV2,PCM,Ethersound) support. |
 |
- Line level (4.2Vpp), unbalanced, stereo output
- 3.5mm headphone jack
- Backlit LCD (2×16 characters), for configuration, status, or title display
- Built-in IR receiver for remote control (remote control included)
|
- 3.5mm headphone jack
- Integrated 2 x 25 watt speaker amplifier (using a 24V power supply or 2 x 4 watts with a 12V power supply)
- S/PDIF optical output
- Built-in IR receiver for remote control
|
| Programmable I/O device server with 2 serial ports, relay and digital outputs, digital and analog inputs and Dallas 1-wire support., |
 |
Modbus remote I/O module with serial RS-485 Modbus/RTU interface, and 6 high current relays (230VAC,16A), UL listed, |
 |
- 4 contact closure inputs with programmable pull-up resistor
- 4 analog inputs, 0-5V range, 12 bit resolution, programmable pull-up (can be used as contact closure inputs as well)
- Contact closure inputs also support use as Wiegand reader interface
- 4 open collector (digital) outputs, current limited
|
- 6 Relays rated at 16 amps, 250 VAC, with normally-open and normally-closed contacts
- Modbus/RTU protocol supported on the built-in RS-485 serial interface
- DIN-rail mountable
- Two extension connectors including power supply and RS-485 signals make daisy chaning additional Barix expansion modules easy
|
| Modbus remote I/O module with RS485 Modbus/ RTU interface, 8 universal (analog or digital) TTL level inputs or outputs. Suitable also as a Wiegand converter or 1-wire temperature sensor interface to Modbus/RTU. |
 |
Modbus remote I/O module with RS485 Modbus/ RTU interface, 12 current sourcing outputs and 12 optically-isolated inputs. The Barix IO12 is a Modbus digital I/O module with a standard RS-485 Modbus/RTU interface. |
 |
- Eight independent configurable inputs/outputs, TTL level, programmable pull-up resistors.
- Modbus/RTU protocol supported on built-in RS-485 (2-wire) serial interface
- Wiegand interface capability (uses 2 inputs)
- Dallas 1-wire temperature sensors can be connected (1 sensor per input)
|
- 12 solid state outputs, rated up to 1.5 amps at up to 30V DC
- Outputs are divided into two groups. Each can have a separate output power supply up to 32V DC
- 12 ESD-protected inputs, optically-isolated in groups of 4 with input current limiting.
|